Go Back > Main Category > VBoost Room

VBoost Room General Bike Discussions

Thread Tools Display Modes

Installed Morley muscle kit
Old 12-10-2011, 06:21 PM
midmoraider's Avatar
midmoraider midmoraider is offline
Senior Member
Join Date: Jun 2010
Location: Missouri
Posts: 283
My VMax: 2004 Tyga carbon fiber
My other bikes: none
Default Installed Morley muscle kit

Hey all, got Sean's jet kit installed today. Had a few issues, of course, but all in all not too bad. I had never messed with the carbs on anything before so I took my time and kept coming in to look at the appropriate stickys on here. The only real problem I had was getting the T hooked back to the bottom of the airbox.

My initial set up is 155 mains, stage 7 needle 2nd clip from the blunt end, a/f 2.5 turns out, shorter springs and the slides were already drilled out. I went with this setup because the carb guru is at the same altitude as me, has a 4-1 exhuast like mine and this is real close to what he is running. The po had put in a stage 1 kit with dynojet 170 mains. These are a little bigger than the mikuni 157.5's and had always been rich. Took it out for a quick spin and HOLY SHIT, this thing sounds badass! The intake sound when you crack the throttle is ridiculous.

Only issue I am having is that two of my carb drains are leaking. They were fine before I opened them to drain the carbs, and I've got them shut as much as possible, but they are seeping gas. Any suggestions?

I guess now I just need to get in on a dyno to really get it dialed in. If you are considering getting one of Sean's kits, I would highly recommend pulling the trigger. Thanks to Mark (Maleko) for the help along the way.
Reply With Quote

Re: Installed Morley muscle kit
Old 12-11-2011, 12:49 AM
maleko89's Avatar
maleko89 maleko89 is offline
Join Date: Mar 2006
Location: Gretna, NE
Posts: 6,481
My VMax: 1999 VMax
Awards Showcase
Nice guy award Bike event award The DOH! award 
Total Awards: 3
Default Re: Installed Morley muscle kit

Great! Remove drain screws, polish the end and put a new Oring on.
Reply With Quote

Re: Installed Morley muscle kit
Old 12-11-2011, 10:12 AM
dannymax's Avatar
dannymax dannymax is offline
Senior Member
Join Date: Jun 2008
Location: columbia county new york
Posts: 12,962
My VMax: '85 Max, 4700 mi, #286
My other bikes: '17 Harley FLRT, '96 test eng
Awards Showcase
Postus Whorus Event organizer award The DOH! award Nice guy award 
Total Awards: 4
Default Re: Installed Morley muscle kit

+1 Usually #40 on the parts fiche, Sean's got them

#40 214-14147-00-00 O-RING
Compassion for animals is intimately connected with goodness of character....
and it may be confidently asserted that he who is cruel to animals,
cannot be a good man.

BRC Carb Shop email/PayPal [email protected]
Ph# 518/392-4024
Dan-o #5127
Reply With Quote

Re: Installed Morley muscle kit
Old 12-11-2011, 02:45 PM
one2dmax's Avatar
one2dmax one2dmax is offline
Senior Member
Join Date: Apr 2006
Location: Derby Kansas
Posts: 14,330
Awards Showcase
Award of Posting Excellence (APE) Mod Monkey Nice guy award 
Total Awards: 3
Default Re: Installed Morley muscle kit

If it's leaking about the screw you need the oring. If it's out the drain hose you need to polish up the end of the screw.

Sean Morley
Our Website - Morley's MuscleCars and MuscleBikes -
first site
main site
Muscle section of the forum
Facebook with a TON of pics:!/pages/Ros...2488678?ref=ts

Bike and Cars: Too many to list!
Reply With Quote


installed, kit, morley, muscle

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -4. The time now is 08:50 AM.

Powered by vBulletin® Version 3.8.2
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd. Exactrep
top of page