Hey guys, I know this is not a Vmax question but don't know where to turn for help. Awhile back I started my Fazer and the throttle was stuck wide open. After a closer look the outer part of the cable slipped out of its resting place that looks like a little barrel on the carb side that is...
I was backing the bikes out of their spots today for their weekly ride and the speedometer cable caught on the forward controls of the bike beside it. Twisted the cable 90 degrees. So when I got on the interstate I looked down to see the speedo was reading 00.00 MPH. I'm sure I could get one...
Luckly wasn't too far from home; choked it back.
Anyone got a write up on replacing the throttle cable?
What particular part do I need?
Any other maintenance I should do while I'm in there?
OK, so I had my Carbs rebuilt by dannymax, and I cannot for the life of me figure out where to install the throttle return cable. It has 2 little cylinders and I only see a place for one. By cylinder I am referring to the part that holds the cable in place. So that's how I installed it. Now...
Anyone familiar with newer cable clutch microswitches on newer bikes?
Like this? Been told there is a Yamaha version. How does it work? Is there something on the lever to push on the switch internally? Anyone have one of these set ups?
I was working on a max and noticed, that I have quite a bit of freeplay in vboost cable, can that be tightened up somehow??
I've noticed before, that my vboost buzzes longer on a power-up than in videos that I have seen in youtube etc. It can be heard when servo pulls just freeplay and when it...
Hey guys , was hoping someone could shed light on my problem. My servo works most of time and moves the black box at end of cable. Problem is the box isnt connected to anything and jut slides back and forth in the metal sleeve. Rather than pulling carbs and fixing has anyone just manually opend...
Hello all,
Removed the carbs last fall but only disconnected #4 from the gang. Replaced them this week and it runs fine but the throttle will not return to "closed' by itself, I have to roll it forward. I thought that the cable routing was incorrect and bound up but cannot find any photos. Do...
I have a new set of bars on the way, which will necessitate extending everything running to them. Now hoses and wires are easy for me. The cables, not so much. I have seen that Motion Pro can make them to order, though they are not cheap. I am keeping the stock throttle sleeve/ switch set up...
Is it possible that a forum-member in UK can order 2 of these cables and resend to me in Denmark ? (I can pay with paypal)
I'll get the Turtle Beach PX5 headset as christmasgift from my wife :eusa_dance:, and have a plan to buy a PS4 next year :o)...
Last year I rebuilt and powdered my masters. I reinstalled them and had a hell of a time to bleed out my clutch. After figuring that I had to bleed the master first and then the line I had better results but either way I dont know if this was the answer or was it just the hours spent bleeding...
Anyone have any input as to options to get rid of or relocate the speedo cable when going to the Tokico calipers? I have a stock speedo currently and without going to something digital/electronic I am not if I have any option to clean that up a bit.
Thanks!
Has anyone installed a negative or positive ubgrade cable kit they use bigger wire for better starting and current flow kits run about 35 to 40 dollars.
I put a SS Vgas throttle cable on last Feb and today it just broke where the cable connects to the handgrip! It looks like a defect cause it looks like it pulled out of the brass grommet instead of the cable actually breaking! I put about 2000 miles TOPS on it and that's just riding on sunny...
My vboost quit working but I figured it out.The black plastic block that the 2 cables connect to(one from the servo motor the other goes to whatever) where it slides back and forth in that metal channel bracket got jammed cockeyed. I got it back in position where it slides freely but it seems...
Hi folks:
Hope everyone's doing okay.
Question: If I specified a specific length speedometer cable I needed, does anyone out there know a person/company who could make one?
Thanks!
Elimax