Recent content by pikipikos

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. pikipikos

    Oil leakage left side - didn't figure out

    As i understand, we are talking about a touch of rtv on the allen threads. Ok. I will do i that.. Thanks for all the advise guys
  2. pikipikos

    Oil leakage left side - didn't figure out

    I have cleaned the area with brake cleaner. I removed the plastic carburetor cover and i noticed that there was oil on the aluminium joint of carb on cylinder #1. The visible allen screw was loose. I cleaned and re tight it. Could it be that? I mean is engine oil moving there, on the carb...
  3. pikipikos

    Oil leakage left side - didn't figure out

    I have cleaned the area with brake cleaner. I removed the plastic carburetor cover and i noticed that there was oil on the aluminium joint of carbs on cylinder #1. The visible allen screw was loose. I cleaned and re tight it. Could it be that? small amount of oil was dripping downwardstaking...
  4. pikipikos

    Oil leakage left side - didn't figure out

    As per the diagram Fire medic posted, on the main crankcase cover NOT the middle drive case(where slave cylinder is located. Unless is the gasket and tricks me out.. But on the other hand, yesterday on a short trip on the highway, the oil was concentrating on the hollow spot of that specific...
  5. pikipikos

    Oil leakage left side - didn't figure out

    Max, the screw i am referring to is at the top of the case cover, starting from 👈 left side, the second one. I dont have any leaks from #21, 22 screws
  6. pikipikos

    Oil leakage left side - didn't figure out

    Hi guys. Its been a while to post a thread. My 94 Vmax was running ok since the rebuild in 2015. I noticed an amount of oil leak, on the left side, concentrated in the 2nd from the left, left crankcase cover allen screw.(i think I've read something in the Forum? about this particular screw) I...
  7. pikipikos

    Help. Help. Cylinder #3 not firing.

    Hey buddy! Do ypu know if there are radial tyres for our stock rims. Front and rear? If yes, which brands are available and what sizes?
  8. pikipikos

    Help. Help. Cylinder #3 not firing.

    Thanks for all that comprehensive info friend! 🤓.. Cheers!
  9. pikipikos

    Help. Help. Cylinder #3 not firing.

    I did resolder the wires. It looks that that was the problem.. 1000 thanks! One more thing guys: i have a friend who owns a 2000 model, crashed. Needs frame anong others. There is an 89 model that is foe sale, parts. The frame can be used for his bike? Can i get the electronics, e. g TCI...
  10. pikipikos

    Help. Help. Cylinder #3 not firing.

    Hi 🔥 Medic! Thanks for the good words. Canada's specs is full power 145hp model. I dont recall the main jet size. I will change the PAJ2's and take it from there! By the way, the f.....vboost controller, doesnt work when cold. I have to squeeze it a bit.. Any treatment? Is hard to get a new...
  11. pikipikos

    Help. Help. Cylinder #3 not firing.

    Thanks friend. I appreciate it. I will order 4 paj2 and hope THAT'S IT😂
  12. pikipikos

    Help. Help. Cylinder #3 not firing.

    Hi guys, I spent 2 days on the wiring. Came out to be the red/white wire on the coil, no continuity! I replaced it, cleaned and rubbed everything up. Measured the pressure sensor, pick-up coil 119ohhms,and all the contacts on the TCI. OK. IT FIRES AT LAST. I took it for ride today morning...
  13. pikipikos

    Help. Help. Cylinder #3 not firing.

    Hello Firemedic. Mine is a 1994 model, Canada specs. In the service manual, speaks about checking the pickup measuring resistance from a 5pin fuse. I cannot see such a fuse. With 5 wires on it. Is the manual wrong? Ok what i do next?
  14. pikipikos

    Help. Help. Cylinder #3 not firing.

    Hi guys. Everything is shitty these days with my Max. I just find out that Cyl#3 is not firing.. Nothing. I had a new OEM COIL. Replaced it. Nothing. I switched between cyl 2 and 3 the coil plugs and is firing. I followed the service manual troubleshooting. And then i discover that i cannot...
  15. pikipikos

    Xjr masters

    I dont really understand all these. Anyway has anyone used the XJR1300 masters? I mean considering oem discs, sumitomos 6 pot and braided lines on an 1994 model.? How is the feeling and what is important is TO SEE IF ITS MORE EFFECTIVE THAN STOCK.
Back
Top