Search results

Hey all back onto my max after some more surgery.. and I had posted sometime back about my clutch. It would slip even after new friction plates, yes the old ones were worn . Changed levers from aftermarket ones.. nope still would do it. Of course I had changed the fluid so I also swapped the...

I had clutch demons for the last 2 years.. haven’t been able to ride much due to spinal surgeries but I’m on the road to ride... bike would slip in all gears so I replaced the clutch. Didn’t help much. Replaced the clutch line with a gaffler braided. Could not get it to bleed came up with a...

Hi do have a clutch master cylinder for sale?? Thanks

Can I get pictures? Trying to figure out what is going on with my clutch.. think I have it narrowed down to master cylinder. Thanks I will Look for pictures

Clutch master cylinder? Thanks

Thank you for your help. I put a new clutch in and it still slip.. most gears and it’s embarrassing! I don’t have much time to do research on the issue. I’m replacing the half plate with a full one .. I will just rebuild the master cylinder. Looking into the the spring.. used to be the DD...

Anyone ever changed out the cans on a Marks exhaust? Looking for something a little linger and quieter.. Thanks

Looking for a good clutch master cylinder. Also DD clutch spring. Thanks

Hey all ! Back after a long hiatus , spinal surgery again... I have had the same issue and had given up due to fact I could not ride my bike... NOW that has changed.. My 97 will slip under hi-way speed acceleration.. new clutch and fluids, running a valvoline oil designed for motorcycles. I...

Thanks for the ideas/help. I will pull the clutch apart a replace the half with a full plate and see if that fixes it. Thanks again

Thanks! All new plates and using motorcycle oil. Did not replace the half plate and not sure which one that is. I get on once in a while and do not get much time to research threads. Sorry just my life. I appreciate the help and if someone can direct me in the direction of the half to full...

Hey all trying to get the max back up and going right after it being stored for some time. My clutch is still slipping after a clutch rebuild.. all plates were replaced. Still slips in the upper gears so I redid the master cylinder and slave cylinder and it's better but not like my other maxes...

HI , just seeing what options I have to open to me. I have a Mark's 4-2 stainless system. Love the sound but its slowly killing my ears.. even with ear plugs. I do sound work and my ears are important and I dont know much about the exhaust options. I bought the bike with the full system...

yes, I put rotella synthetic in .. so can I just drain and refill with conventional oil or do I have to do something else.. I still am going to check the master cylinder out . Trying both tomorrow. THANKS

I am using plain dot #3 brake fluid and I am about to work on it tomorrow! I had the alignment issue last year when I changed the clutch.. I will first check the master cylinder and move on from there.. When the clutch slips its quite a bit in any gear. Taking off normally but any load it...

I will cover the bike and try it again.. I did not pump the master cylinder with the cover off.. sorry 1st time when I did it..Thanks for the advice. TIM

yes and nothing came out.. will do that again. The clutch seems to pump up ok..

Well last year had clutch issues.. 35k on the bike and slipped bad. Changed the clutch and fluids in the fall rode it and seemed ok.. but the bike just didnt have the power my other max's had.. This one- marks 4-2 - morleys air box mod and carbs . Been on several rides and seemed about the...

Helping sell for a friend. Located in Indiana. Super clean! Sharp dresser with low miles. Always garaged and taken care of. New tires and brakes, with Harley pipes gives it a great sound. Pictures do not do it justice.. Just dont ride it so selling it. PM or [email protected]

Had posted earlier about needing help on my 1st clutch change and it really was easy, especially with all the help.. now after about 30 miles on it is still slipping, sometimes right when I start off or after its warm... slips in about every gear.. :ummm: been reading some posts but dont want...