Search results

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. S

    Parts For Sale 2020 Stock rider seat with flip forward piece

    Excellent condition, no tears, rips, etc. Grey stitching. Asking $250+shipping. Shoot an email to [email protected]
  2. S

    Air filter cleaning

    For those with a K&N filter, how often are you cleaning/re-oiling the air filter? Service manual says to replace the filter at 24K miles so I assume that would be a good guess to clean it, or maybe a little before.
  3. S

    Keyed power for speedo healer

    Got a speedohealer on the way. Was wondering what keyed power wire can be used that is close to area beneath the seat?
  4. S

    Parts For Sale Gen 2 black stock foot controls - SOLD

    Everything is in good working order but the brake lever was damaged from a tipover. It's not very noticeable since most of the scratches are only seen from the underside of it. Didn't feel like trying to find the connector for the brake light switch so I cut those wires but there is enough to...
  5. S

    Parts For Sale Brembo 17 RCS clutch master cylinder

    Tried using it on a gen 2 but didn't work as I had hoped for. Used for about 300 miles. Comes with banjo, crush washers, tygon hose & reservoir cup. Asking $250 + shipping. Send email to [email protected]
  6. S

    Parts For Sale sold

    Sold
  7. S

    1400 rpm idle

    Other than a vacuum leak, what would cause a slightly increased idle? Bike runs well, no obvious loss of power & occasionally, it idles down to 1K. Started happening immediately after changing to a round headlight setup & stainless brake lines with Brembo brake/clutch master cylinders.
  8. S

    Electrical fitting on clutch master cylinder

    What does this fitting do & what happens if it's unplugged?
  9. S

    Speedo/tach harness connector

    Does anybody know if the speedo has a connector or where it's located? The bundle goes below the top triple & into the opening in the right side frame but I could not find a connector anywhere along the way. The speedo gauge will not fit through the opening of the headlight frame either.
  10. S

    Parts For Sale Pro Taper contour Carmichael bend handlebar for gen 2

    Bar purchased new, used for about a week. Dimensions are as follows but a quick description is they have about the same rise & width but with less pullback so it leans you a bit more forward than stock bars. A (Width): 800mm B (Height): 77mm C (Rise): 36mm D (Clamp): 195mm E (Sweep): 55mm F...
  11. S

    Throttle body sync issue

    Synced my throttle bodies recently & came across this issue...both rear cylinder's screws are completely turned in, no adjustment range left. The right front cylinder still has adjustment. Left front is the standard. What happens when they won't sync the next go around?
  12. S

    Front brake size

    Does anybody know the master cylinder bore & ratio? I know the bore is 16mm but radial masters are designated 16xXX, second figure being the pivot to plunger distance. The best I can come up with is 20mm but I really would like to know what unit Yamaha decided to use & I cannot find that info...
  13. S

    Windowed covers

    So besides Otec, what other options are there for these covers on a Gen 2?
  14. S

    Parts For Sale Stock gen 2 seat

    Seat has been shaved down about 3/4" towards the front. Asking $225 + shipping. Contact [email protected]
  15. S

    Parts For Sale Gen 2 Windshield

    Asking $175 plus shipping. Send email to [email protected]
  16. S

    Anybody have the Corbin front saddle?

    Just looking for a review before spending the money.
  17. S

    Avon or Shinko?

    Haven't decided which way I'm going but I'll need new tires soon. For those that went with the Avon Cobra Chrome 200/55, what front did you get? They don't make the cobra chrome in the stock size. If you run a shinko out back, did you get a shinko up front or another brand?
  18. S

    Parts For Sale Pro Taper bars for gen 2 - sold

    The bar has a little less pullback than stock. Aluminum, 31 1/2" wide, 4" rise, 2 1/4" pullback. Asking $60 + shipping, email [email protected]
  19. S

    Fork spring removal steps

    Can someone confirm I've got this right...after removing the cap from top of the slider & the damping rod tube, does the spacer, seat & spring come out?
  20. S

    Bike not tracking straight after tipover

    Found my bike laying on it's right side. Typical cosmetic stuff damaged but riding it home I noticed the bars have a slight left twist to them. It's not just the bar, the top clamp is turned too. How much chance is there the forks are bent? There isn't any obvious damage. The bike felt off...
Back
Top