Search results

For anyone that is tired of messing with there carbs and does not trust the local shop with there vmax carbs send them to Dan. He did an excellent job on my carburetors. Turn around was extremely fast. Communication was excellent! I installed the carbs last night bike fired first try idled...

I'm tired of messing with my carbs. Not sure they are the issue or not. I have nobody locally that I would trust with them. Who would be the best and most trustworthy to send them to? I have a stage 7 with vboost fully removed. Thanks for any help.

Like the title says how do I go about syncing with a jet kit? Thank you

My float is stuck open on a carb and gas is pouring out the overflow. I need to ride home about seven miles. Can i plug the overflow and ride it home?

Just some pics of the mostly finished vmax. 6" over swingarm (morley's muscle) 18" rc rear wheel absolutely amazing upgrade for vmax handling (radials) complete tear down for painting. tail section (morley's muscle) People cant help but stare

I finally got my vmax running today sort of. The left front cylinder and left rear cylinder are not firing. There is no spark. The plugs are new. The entire bike was disassembled for repainting including wiring. I am not sure what would cause this or how to start diagnosing it. Thanks for any...

I installed new front turnsignals that do not have running lights. I am wondering if this is causing my led brake light to stay on constant? I see in my wiring diagram that the front turnsignal wiring runs to the brake light. could this be the problem? How would i fix this? Thanks for any help.

I bought a mityvac today hoping it would make the brake/clutch bleeding easier. I had all the fluid out of the masters and put new ss lines on. I have pumped about 12 oz of fluid through the front calipers. Does it normally take alot of fluid to get the air out if so about how much 3-4 12oz...

My right fork is leaking oil out the damper rod bolt. I compressed the forks all the way and damper rod still spins and i cannot tighten the bolt. Is there a trick to this? forks are on the bike.

hey gang i have a mystery to solve. Bike is almost back together but i have a couple of mystery parts. Hopefully someone can help identify them. 1st i have a small hose, i know i have seen this on the bike because it is very familiar but i just cant figure out or remember where it goes. 2nd...

Is there a good way to find a leak in the radiator? I have it off the bike now and what to find and fix the leak. Can i plug it up fill it with water and shoot some air into it to find the leak or can this damage somthing? Thanks.

I dont have an allen socket for my torque wrench. I think the torque is only 4 lbs. I just tightened it until the swingarm had no side to side play then gave it a little snug. Is this ok or do i need to go buy some tools? Or does anyone have another way of doing it? Thanks

Sorry for all the post lately but i am hoping to get the max mostly back together this 3 day weekend. I am putting the harness back in and i am not sure how the harness gets to the rear of the bike. does it come up under the fuel pump or around the coolant reservoir? I should have taken a couple...

What would be the best way to clean my wire harness? It's grimy from all the years and I want it to look like new before I reinstall it. I have no idea what would be a safe way to do this. Soap and water? I don't want to just tape and wire loom over the dirt. Thanks again for the input.

anyone buy the cheap ebay brake pad sets? 30-40 $$ for fronts and rears are they any good? I might try a set and see.

I am puting the engine back in my frame today and i am wondering what should be installed on the engine first. The only thing i have put on is the intake manifolds. Is there anything else that will be alot easier to put on now before its in the frame? thanks

Has anyone powdercoated there engine. I am thinking of doing but have a few questions. Will the engine overheat with powdercoat? Do i have to disassemble the engine to do it or will all the gaskets and rubber parts hold up to the baking process? what holes need to be plugged besides the...

What is the best website to buy tires? I have the stock front wheel and a custom 18" rear wheel. I was thinking of geting 110/80/18 for the front and 180/55/18 rear (radials). what is the best set of tires in this size and where should i get them from? Also is it safe to use 120/70/18 on the...

First off I would like to say hello. I am a newby. I just bought my 93 vmax about a year ago from my dad who bought a new starmax. I like the way this bike runs, but i do not like the way it handles or looks. The last 10 years i have been riding sport bikes and i love the instant response in...