Search results

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. A

    Need a foot shift lever for Gen 1 Max

    My bike feel off the kick stand and bent the foot shift lever. Its cast aluminum and I bent it back as much as possible but any more and it will snap. Let me know if you have one. Thanks
  2. A

    2006 Stock Exhaust for Sale (Not perfect, but pretty good, and cheap)

    The title says it. Check out the pictures. I would like to get this out of my garage. How does $100 sound shipped? Fifty for my time and fifty for shipping. Thanks https://www.dropbox.com/sh/12vxo9kfw3ul3hp/AAChe6o8H50xbu6xkcMLPsWVa?dl=0
  3. A

    Help choosing Master Cylinders

    I'm in the process of upgrading brakes on 06 vmax. Front will be 320 mm rotors, Hayabusa 6 piston on both sides, new lines (Goodridge Sniper 2), and new master cylinders for front brakes and clutch. Clutch will be DD. Trying to figure out which route to go on MC bore size. I previously used...
  4. A

    Suggestions for stainless 4-1 that is not too loud

    I'm looking for a 4 into 1, all stainless, and reasonably quite. Louder than stock is ok but want it to be comfortable to ride. My last exhaust I bought was a UFO and I had to wear ear plugs when riding the bike. Any suggestions? Thanks, Aaron
  5. A

    Looking for OEM grab bar

    My 07 has a sissy bar but want a grab bar for when I riding by myself. Thanks, Aaron
  6. A

    Rear grab bar

    Does anyone have a rear grab bar? My bike came with the factory back rest which I want to keep but when I'm not riding with my wife I want to swap out to the factory grab bar. Paint condition does not matter because I will powder coat it. PM me if you have one for a good price. Thanks
  7. A

    DIY Oil pressure gauge

    Updated 3/12/18: If anyone wants to DIY the oil pressure gauge: 1. The oil galley plug - I believe this is M20x1.5 thread. So M20x1.5 w 1/8 NPT in middle to accept fitting. These are available for around $10. Exhaust Temp Temperature Sensor Adapter M20x1.5 20mmx1.5 -1/8NPT on fleebay 2. Marshall...
  8. A

    Bike Resto in Full Effect Pt#2

    p { margin-bottom: 0.1in; line-height: 120%; }a:link { } It has been a while since I post. I documented my last build which can be seen here: http://vmaxforum.net/showthread.php?t=26991&highlight=resto+full That bike ended up getting totaled in North Carolina by family member (they were...
  9. A

    good container for under rear seat?

    Im trying to find a container that fits under the rear seat that will hold my wallet and phone and is water proof. Any ideas? Thanks
  10. A

    Need to replace my clutch disks

    My clutch is starting is slip and I want to replace the disks. While I'm in there I might as well fix that shifting issue earlier Vmaxs have. My questions is exactly what parts do I need? Here is the list I have so far. (8) Plate, Friction 3 item: 26H-16307-01-00 (7) Plate, Clutch 1 item...
  11. A

    What resistor for COP conversion

    What resistors are you guys using to convert to COPs. My stock coils primary is 3.0 ohms. My Denso sticks are 1.3. So what is everyone using? 2.0 ohm, 50 watts? I have a feeling people are using smaller resistors since it's not constant current.
  12. A

    Weld in O2 sensor bung location

    Can and O2 sensor be welded in near the end of an exhaust system or does it have to be right on a primary near the engine where it is hottest? I've always had the impression that O2 sensor need to be very hot to operate correctly but my exhaust is ceramic coated. The "muffler" at the end isn't...
  13. A

    Help identifying this bracket

    Can anyone identify this bracket that One Off uses for his oil kits. I would by it from him but I don't need to wait a month for a bracket :ummm:. http://www.cycleoneoff.com/2012-10-22_14-19-20_963_op_800x450.jpg
  14. A

    Low voltage/ not charging

    I've gone through RaWarrior's how-to on taking care of low voltage. I fixed the crimp in the harness, replaced the r/r with a mosfet version from a zx14, replaced the battery, added connections directly from the r/r to the battery, and I finally replaced the stator yesterday. It's still not...
  15. A

    3 most important gauges

    I was wondering what everone thinks are the most important gauges to have on a Vmax. Lets disregard the speedometer and tachometer for a second and focus on everything else. The ones that comes to mind for me are oil pressure voltage fuel pressure water temp oil temp air/ fuel wide band...
  16. A

    Good turn signals

    Who makes good turn signals that aren't from China. I'm tired of buying Chinese crap and having it fail a month later.
  17. A

    Adapter for Hayabusa caliper on rear?

    I've got the 300mm wave rotors and a hayabusa caliper I want to put on the rear to match the front. What bracket do people use who have done this?
  18. A

    intermittent electrical issue

    My headlight is going out. At the same time the gauge illumination goes out. To make the lights turn on and off I turn the handlebars. Any guesses at the cause? I keep looking at the electrical schematic and I'm coming up blank.
  19. A

    What size main jet for stock setup with full exhaust

    Danny has my carbs and I was wondering what a good size main jet is to start out with on a all stock drive train minus a full length UFO 4-1 exhaust. Thanks
  20. A

    What size master cylinder bore

    I'm thinking of changing both master cylinders on the handle bars to some newer Nissin units. I rebuilt the stock Vmax ones and one is leaking and I don't like how the powder coating came out. For the clutch MC, I assume I should stay with the bore size that the stock MC has. I have 6 piston...
Back
Top