Search results

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Ctshooter

    Reversing the "drill holes in muffler" mod...

    When I reversed my exhaust mod I used a generous amount of high temp red rtv around the perimeter of the holes, then re-rivited the plates on and let it set up over night. No leaks and have been running them for a year now. I would imagine how well it seals is determined by what location the...
  2. Ctshooter

    Low Voltage Readings

    Well, I cleaned the ground to the regulator, frame ground under the seat and all my battery connections, and plugs under the seat. I then lubricated the connections with dielectric grease, retested my readings and I am now getting 13.8 volts at 2500 rpm. My battery tested at full charge using a...
  3. Ctshooter

    Low Voltage Readings

    I did the crimp fix a couple of years back, so thats set. I will try cleaning the ground wire connection point on the frame and the RR plug and see what that does tonight and will post results. Thanks!
  4. Ctshooter

    Low Voltage Readings

    Hi all once again. A strange problem has surfaced with my 95 max recently and I believe it is a regulator/rectifier issue but am not too confident with checking things out using the fault finder. Electrical has never been my cup of tea and I don't want to burn something out. :ummm: So can...
  5. Ctshooter

    Spacer length when using front spring mod

    When I called Progressive, they told me to set them 5/8th of an inch sticking out above the fork with the suspension hanging. I haven't tried it yet to see how it feels.
  6. Ctshooter

    Spacer length when using front spring mod

    :ummm: Can anyone give me a ballpark spacer length to start with when using the progressive lowering kit and emmulators? I tried what one person posted and the spacer stuck out of the tube about 3" and couldn't even push it down to get the fork cap started. Seems a bit much to me. Thanks...
  7. Ctshooter

    Frame braces

    Does anyone know where I can find a pair of new or used bolt on frame braces? I can't find them on the links I have. Thanks..
  8. Ctshooter

    Leaking fork seal again!!

    Hi all. This is the 3rd seal replacement in about 4500 miles on my right fork tube since I did them both at about 2200 miles. My bike is a 1995 with 1,013 miles on it when I bought it 2 years ago. I now have 8600 miles on it and my left seal is fine and not leaking. After cleaning up my right...
  9. Ctshooter

    500th POST CONTEST, ENTER AND WIN BITCHES!

    Re: 500th POST CONTEST, ENTER AND WIN MY BROTHERZ! 3.8
  10. Ctshooter

    Carb parts needed for total rebuild

    What do the coasting enrichers do? If the diaphragms were to dry out and lose their elasticity, what conditions would be the result?
  11. Ctshooter

    Best pipe?

    I have the new megaphone design UFO pipes on mine and they sound great, but your ears will be ringing if ya wear a helmet for a 3 hour ride. I'm looking to get something more toned down. I talked with Marks, and I think I will be going with his, although he has a 4 week backlog as of now. From...
  12. Ctshooter

    Exhaust pulse uneven

    How do you clean up the pilot circuit? I'm green at this. Thanks...
  13. Ctshooter

    Exhaust pulse uneven

    Hi all once again. An update on my earlier post concerning jetting for UFO pipes. I did the carb tuning sequence that was in this post and all is fine. Still feels fat in the midrange and I get sort of a flutter sound from the engine/exhaust when between load and no load cruising around 3,500...
  14. Ctshooter

    Jetting for UFO 4 into 2 exhaust

    Thanks for all the help everyone. I'm going to try the carb setup procedure that Maleko89 recommended and see what I get. I"ll post the results. Who is Gainey and how do I contact him?
  15. Ctshooter

    Jetting for UFO 4 into 2 exhaust

    So is there any aftermarket pipe that does it all? Or, are we sacrificing power to have the great sound?
  16. Ctshooter

    Jetting for UFO 4 into 2 exhaust

    Yes, I'm using the shorter springs and drilled my slides as Dynojet recommends and using 165 mains and the Dynojet stage one needles postioned on the 3rd clip. Unfortunately, I should've ran the pipes with stock setup first and see how they work, but in waiting for my pipes to be done, 2 weeks...
  17. Ctshooter

    Jetting for UFO 4 into 2 exhaust

    Hi all. I was wondering what everyone is running for Stage One jetting with these pipes. Sound awesome! Jon at UFO says to use 165's and put the clip in the middle notch then turn out the adjustments to 2.5 turns. Why does Dynojet say to use 170's for the mains? Reason I'm asking is because the...
Back
Top