Search results

can anyone tell me what will or might happen if you run Noology wres with a standard NGK resistor plug. Noology states that you have to use a non-resisitor plug, but I have read on some posts where individuals are using standard NGK plugs with resistor. Thx:ummm:

http://www.knickerpicker.com/dressing-room.asp Provided by Gaijin-Riders :punk:

Can anyone tell me what the benefit of using a floating rotor as to a non floating rotor. Do you get better braking distance??, Are certain calipers only made for a floating rotors. Thanks, Ron :ummm:

Good for a laugh http://www.youtube.com/watch?v=ukAhlxl4hmM

Started to encounter a problem today with my boost kicking in while at idle and seem to be getting worse. I have the Sasy controller on and the yellow v-boost light started to flicker and then go solid, and the engine would stall. I will only have the bike on the road for another couple of...

I having a problem with the fuse for the fan, it keeps blowing when the fan should be kicking in. I'm thinking there is a short somewhere?correct, if not what should I be looking at, to either test or replace. Thanks, Ron :cheers:

Does anyone have any suggestions on how to remove an altenator cover that will not budge, yes all the screws have been removed, there is no oil or coolant in the bike so I cant start her up to warm things. I tried with a heat gun but no luck thanks, Ron :ummm:

Riding home today and I was having problems getting the bike into 4th and 5th gear, 1-2-3 no problem, but 4th and 5th espically at the higher revs. Any thought or suggestion would be greatly appreciated. I took the casing off and took a look at the plates and discs, I really dont know what to...

can anyone tell me when you turn your ignition on do your lights come on ?. Seems that the previous owner installed a FJR1200-1300 right handle bar switch, when I went to replace the faded worn out one with a newer used V-Max one I noticed the diff. I have to manually turn on the lights, as well...

Can any tell me if you can replace the older forks with the newer stock forks. I have an 88, and there is someone selling the fork tubes, + Emulators, progressive springs, fork seals/shields, fork brace stabilizer. Will the older front fender fit, are there any other parts required...

I have never experienced a high speed wobble until this weekend. I was out on the bike on a stretch of highway when I opened her up and off I went at one point the bike started to wobble, scared the shit out of me. I have never experienced this before, I rode most of the day cruising between...

I have a bunch of spark plugs that got fouled when I had problems with my carbs, I got some of the black off, is there a solution or product that I can apply to clean them. Thanks, Ron :ummm:

Has anyone ever changed the drain cock assembly (DCA) if so was it difficult, mine is leaking from the on-off nut when the engine is cold and the temps is below 10 degres. I would imagine its from the contraction and any worn o rings in the assembly Does the DCA simply pull out of the...

Any way of testing the temp gauge, the fan seems to be kicking in at half way 3 Oclock, normally it would only kick in past the half way mark, not sure if it the gauge or something else.:ummm: Thanks, Ron

I have Brembo calipers on the front, the heads of the screws are a bit rusty, does anyone know if I can simply replace the screws, or do i have to strip calipers down to replace them. Thanks, Ronr

Can anyone tell me where I can find a detailed thread on the fubur fix, perhaps with pictures. Thanks, Ron:confused2:

Had the bike out over the long weekend and my buddy was telling me that he smells gas comming from the exhaust, I too smell it when I start up. I took the plugs off today and 1 is wet fouled, smells like gasoline, the other 3 are fine. Will adjusting the air/fuel mixture screw fix the problem...

I know I saw a thread about cruising at 4000rpm then crack open the throttle, what gear are you suposed to be in and what are the end results. Thanks, Ron:cheers:

Well I finally got my bike back from the shop, and it works, had no other choice, just couldn't get the bike to work, turns out that the Keyster kit that I purchased on-line from ebay, the pilot jet, and the needle jet were incorrect, pilot jet had the correct # but was not the proper size...

Well I had the carbs apart again, cleaned them all out, not that they were dirty, everyting went back where it should, all screws tight etc. still cant get over 3000-4000rpm. I dont know what the freaking problem is, I got good spark on all plugs, compression is good, carbs synced, it just...