block

Ok I had dramas with the carbs..so I pulled them off the bike and started dismantling them.I have reached the point of removing the jet block and it seems stuck.I tried levering it off with a large screwdriver but it doesn't want to budge.Any ideas on how to remove them would be great.Thanks...

I have a 1989 bike that is in great condition however both right and left switch block controls are flaking their paint. Obviously painting them black is no issue, however the small writing is going to be lost... as the lettering no is not “indented” it seems to have been printed on... Has...

Was having trouble pushing the carbs block down so it sits properly. Resorted to approach attached. Laugh all you want, but it works! :-) Hope this helps others!

I am quite amazed at the prices for the little rubber plugs in the pilot jet block (called "caps" on the parts breakdown). I'm not going to spend 60-70 bucks on one set up of them (8 ea.) What have owners here used to replace messed up rubber block caps? (pencil erasers, lol?).

http://www.reuters.com/article/us-south-carolina-pornography-idUSKBN149251 A religious/conservative group trying too inflict their own ideals on everyone with more anti-choice legislation, or a money grab? We have to prevent "millions of lives" from being destroyed. Or, or you can just slip...

I've been having these issues for a few months now and not been able to ride except around the block after a couple shotgun attempts. I've replaced the fuel filter and plugs, checked the fuel pump, checked the tank, seafoam a few times and shotgun 3 times to no avail! It pops, sputters, and...

A wise guy had drilled a 1 inch hole at the bottom of the stock muffler. Did someone found a simple way to block it? Thank you Eric

Is it possible to put Vmax heads with their bigger valves on a 1300 Venture block without major issues? What mod are required? Notching pistons?

Would loose jet block plugs make a bike seem (or actually be) really rich, especially at idle. I know I've got an exhaust leak, but this seems to smell pretty rich even for just idling. Morley Jet kit,stage 7 needles (3rd clip), stock springs, 152.5 mains, non-drilled slides, Hindle 4-1, a/f...

I haven't been around much lately as my health is declining fast. Today was one of my good days so I got the bike out to rebuild the carbs again. Ethanol fuel really plays havoc with mine. My stupid question involves the rubber plugs that go in the jet block. The plugs have a flat edge on them...

Looking to borrow/rent a "Gas Block Barrel Dimpler" for my: 18" rifle length gas, Shilen Ultramatch, .223 Wylde barrel. .750 I'll pay shipping and thank you.

Hey, guys, Does anyone have a source for the rubber plugs in the jet block other than the 5-dollar OEM's from the online sources? For that price I'll just single-point a brass plug and thread it into each one but it is more work than I want to do. Thanx, Bud Sent from my iPhone using Tapatalk

Was enough for me to appreciate how awesome my Vmax is..... I bought the Super about a month before the Vmax. I had a V65 Magna and was looking for a Vmax. But I couldnt turn down the price on the V65. So I bought it. Worked on it a little and then the Super popped up. So I bought that, rode...

Trying to clean up some electrical stuff. Anyone know where to get those very small pin terminal connectors? (not reg size but small..for LED type wires)

I have a couple of questions about this build I'm in the middle of, and would appreciate the forums input. This motor is going into a max. 1. can venture rods be used? I know they are the same size as the max but are the max rods better? 2. what should I use for head gaskets? 3. would...

http://www.fastcodesign.com/1664757/meet-ed-jacobs-designer-of-americas-meanest-motorcyle How come I never heard of Confederate Motorcycles? Does anyone have some background info?

Hello, just took my carbs apart to set the float levels, while apart i would like to check the pilot jets and clean them how do i get the pilots out or should i say take the jet block out????i took the two screws out but its not coming out so before i break something i will ask what im missing???

posting requirement? post pics!

ok, trying to figure out what seals the tube at the insertion point into the block - cannot see any seal or o-ring listed on the diagram. :bang head: the drain tube below the radiator - where it inserts into the block is leaking. anyone have any ideas or has anyone replaced this tube or had...

I'm proud to say I contributed.:hihi: Hey Big O! Take your Marxist chit and swim back home. :nyah nyah: And kiss my :10_6_8: before you dive in!!! JEFFERSON CITY, Mo. - Missouri voters on Tuesday overwhelmingly rejected a key provision of President Barack Obama's health care law, sending a...