install

Hi, Just bought and installed UFO exhausts. Looks and sounds awesome! two question though; - How much should i tighten the exhaust gasket clamps? I tightened them until the can't move but the mufflers can still around the midpipe. Should I tighten it more or would i be fine like this...

So I got the bike a few months ago, and my ambition finally kicked in to install the Kerker 4-2-1 with a Supertrapp silencer that came with the bike. The owner prior to the guy I got the bike from had installed it and did the re-jet. The OEM was re-installed to make a wife happier. Yowza...

Stupid question!! I can't find another hose where does the small port at the top of picture underneath airbox go??? Sent from my SCH-I535 using Tapatalk 2

Stupid question!! I can't find another hose where does the small port at the top of picture underneath airbox go??? Sent from my SCH-I535 using Tapatalk 2

Hello, I'm trying to reinstall the stock vboost system after removing an S7 kit; I want to put the bike back to OEM. Not having done this before I'm having a few challenges. My immediate problem is that I don't see an easy way to install the 2 screws that hold the servo/ motor thing in place...

good morning brothers, just have a quick question i'm sure you can answer i've finally picked up a factory backrest for my 92 so the wife does'nt feel left out everyday staying home and wanted to know if i'm going to need any new hardware to put it on, or if you just use the bolts that are on...

First things first, gotta thank Ost85vmax for sending me this switch setup... I really appreciate it bud!!:clapping: The first thing I did was to get the sensors figured out and I gotta also thank NHVmaxpower for his review and install because it saved me some time because he gave the tip about...

hello all, maybe someone can help me i purchased a set of led signal lights for both front and back did get the 3 wire wanted my running lights, anyway did the diode install, installed the flasher ELFR-1 Flasher Relay, turned on the key and i get one side leds stay on but dont blink, other side...

Since it is too brisk to ride, I am wondering on how to make my day useful. Along with installing a manual fan switch I decided to install a 12 outlet. Since we depend on our phones/smart phones, what are the chances of being out and then phone dying? I have been there with the car, but out...

I've had a lot of bad experiences with people damaging the finish on wheels when installing new tires. So who do you trust to do this without damaging the finish on a wheel?:ummm:

I got a set used on ebay and it didn't come with any fasteners, washers, etc. Curious if any of you guys have the install instructions you might be able to scan or know where I can find em. Just looking for a parts list and what fasters are to be re-used (if any) and what I should run out to...

Hello, I'm going to put progressive springs in the forks and I noticed that if I ever want to change my fork oil in the future I will have to remove the forks or turn my bike upside down, I'd rather have drain plugs to drain the fluid. It looks like there is a place to install plugs if I wanted...

I am hoping someone has some expierience or thoughts on this. I have made a completely custom guage cluster and have switched all the bulbs to leds. I new I had to replicate the resistance for the fuel light and that is working correctly along with all the other bulbs except for the turn signal...

Hi guys. New to the forum and appreciative of the knowledge here. Working on rear tire change on a 2009 and have been fighting reinstalling the differential/driveshaft for way too many hours. Not my first drive shaft install and usually no problem. Aware that this model has the one wider...

So I'm just going to say it that I"m not too savvy with Bikes...:ummm: all I know is how to ride them fast. and oil change....beyond that nothing.. however I'd like to change that with this bike...I want to start doing thigns myself...so start off, how hard is it to install the UFO link? Has...

Ok, so after looking all over I found this Glowshift Digital Tach/Shift light combo unit that was small and I really liked it: It was like $54 shipped, had the mount curved to fit the speedo bucket, and i think looked sharp. After searching around on the forum, it looked like Rawarrior also...

Installed my new belly pan today!!

I have tried searching using words like morleys muscle jet install* fit* blah blah blah and I get like a gazillion posts that have some of those words in it. Is there a how to guide anywhere? The instructions on Seans website are pretty short, and I can't work out what I should do to start...

Hi guys, I have been wanting to install a 4 way flasher feature on the bike. I was thinking about following the diagram attached, but don't you think it's a bit overkill ? Any suggestion about a simpler way of doing it ? Thanks Michael

Hey gang, I received my HID kit from DDM Tuning in the mail a couple days ago. I have no clue how to install it and it came with no instruction at all. (and apparently my search skills are broken today!) The only guide on their website is for a car, can anyone point me to a write-up on the...