jet

Hi, I just rebuilt my carbs and when i put it back fuel was pouring out. So i removed the airbox to see where fuel was coming from and it's pouring out the air jets. I tried to cover them with the fingers, the it came out of the tubes that go to the airbox... When i rebuild the carbs i...

I haven't started on it yet, so it may be obvious when I get into it, but what's this?

Hi, I just installed Morley Jet kit and now it sucks at higher RPMS, I cant even get to 6000 RPM. I did this while i was cleaning my carbs and my new exhaust hasn't arrived yet, so it's still on stock exhaust. The problem is i read CV carb tuning guide and it says if it doesn't pull well my...

Hi, I just bought Seans Jet kit. Do I have to remove the carbs to clean the inside and rejet or can i do while it's still on the motor? Thanks!

Just put My stage 7 in over the weekend and just ran across this..:punk: So if anyone is looking a for one heres your chance:confused2: 2 weeks ago I would have been trying to get it..:rofl_200: 17 hours left...

I haven't been around much lately as my health is declining fast. Today was one of my good days so I got the bike out to rebuild the carbs again. Ethanol fuel really plays havoc with mine. My stupid question involves the rubber plugs that go in the jet block. The plugs have a flat edge on them...

I have started rebuilding the carbs on my 85 vmax as the bike was sitting 9 years before I bought it. On the first carb I have disassembled. The pilot jet appears to have been soldered closed (?). I'm able to look down inside all of the passage ways with a high end (aka expensive) micro scope at...

Hello folks, and Happy New Year! I've just installed Mark's stainless 4-2, 2" exhaust and the bike started running lean / lacked torque. Then installed Morley's Jet Kit with needles on 4th clip, Mains 160 (2300-2500 ft elev, 47 degrees outside) and I suspect it's running too rich. The...

hi guys santa might be get me a jet kit stage 7 or morley muscle i have read the other threads on the kits and i think i would like to go with the morley muscle kit but will i feel much of a diffrence and how easy is it to fit and would i need to get it ran on a dyno cheers guys

Hey, guys, Does anyone have a source for the rubber plugs in the jet block other than the 5-dollar OEM's from the online sources? For that price I'll just single-point a brass plug and thread it into each one but it is more work than I want to do. Thanx, Bud Sent from my iPhone using Tapatalk

So now that I have the racing bug, I have a question. I ran 7.28 (1/8th) with several other passes in the low 7.3's. my 60 ft times were around 1.8 with a best of 1.77. I see I have room for improvement on the 60 ft, so with pratice I can see being consistantly in the 7.2's. Would a jet kit, set...

is there a big differance over Seans jet kit set up over a Dynojet kit besides the Dyno jet kit i think runs maybe around 100.00 and has no modified airbox .I have a two brothers racing 4 into one header and exhaust set up .I am not sure what i am running for jets but i get 30mpg even when i...

Hey guys, I picked my bike up from the shop that jetted my bike they tuned it by ear.... It didn't seen to bad going around the block... When I got on the highway I noticed it was really rich and was loading up at crusing speed. Under wide open throttle it seems very rich as well... I have a...

how can I clean the pilot jet without removing the carbs, will the shotgun or pea shooter do it?

How hard is it to install a jet kit? What would it do performance-wise...I have a full exhaust system and a K & N filter?

Hi. What V-boost setting would you recomened with a muscle-kit for most power? I'm having it installed and setup next week and wondered if it needs to be left in the v-boost setting it's setup in; ie 3.5k or 6.5k rpms. Either that or have it on full time. I've a full exhaust system if thats of...

I just went for a ride after putting in my Morleys jet kit. My setup is I used Seans needles (stage 7?) Put in the air correctors 157.5 mains STD springs Idle screws 3.25 turns out V-boost programmed to start opening just before 4000RPM Seans airbox lid Marks exhaust 4 into 2 The main...

I have tried searching using words like morleys muscle jet install* fit* blah blah blah and I get like a gazillion posts that have some of those words in it. Is there a how to guide anywhere? The instructions on Seans website are pretty short, and I can't work out what I should do to start...

Ok just got another set of SS super trapp slip ons , they came off of a 2005 model. Along with the trapps, he gave me the mains that h=the shop took out. They are 170, that is the size that his local yamaha shop installed to run with the slipons. He was only running 7 discs? I am confused, Will...

Hey everyone I've had a vmax for about a year now. I love this bike. Dreamed about one for years, I found a 1986 with custom pin striping in PA with only 3000 miles on it. Anyway I put cobra 4 into 2 exhaust on it and I want to debaffle the cobras. The carbs are stock and the intake box is...