signal

hello all, maybe someone can help me i purchased a set of led signal lights for both front and back did get the 3 wire wanted my running lights, anyway did the diode install, installed the flasher ELFR-1 Flasher Relay, turned on the key and i get one side leds stay on but dont blink, other side...

I'm installing new led turn signals and have seen the restistors to install inline but just came across a led flasher? has anyone tried running this flasher CF13JL02? thanks

Can anyone tell me why (more often than not) when I am cruising and have my turn signal on and hit the horn that my 10A fuse blows? I have led turn signals on the front and the cbr conversion on the back. Both have resistors wired inline. Also, when that blows, my tach and temp guage go...

I am hoping someone has some expierience or thoughts on this. I have made a completely custom guage cluster and have switched all the bulbs to leds. I new I had to replicate the resistance for the fuel light and that is working correctly along with all the other bulbs except for the turn signal...

As some of you know, I've the infatuation with LED's. I've got about a dozen projects in the fire right now for LED upgrades on my Vmax. The most recent being a replacement for the stock turn signal bulbs on the front of my motorcycle. I plan on replacing the rear break light and turn signals...

Hi there, I have a (mayby simple) question. I noticed lately that the front turn signals do have an other bulb (twin bulb) then the back bulb (single bulb) Also the front has an extra wire (blue) for powering the twin bulb at the front. But in my 96 bike is this wire at the front not...

Need new or used front three wire turn signal bulbs. 1987 Vmax 1200

I changed rear signal lights,had a short at new light,and blew the fuse.Fixed the short,and replaced the fuse.Fuse does not blow now,but signals still do not work.Is it possible that something else blew.like a flasher relay,or something like that.Or did i fry a wire somewhere.

Hello All, I just recently had my 16k mile service performed and when I got my bike back, I discovered that I have no running turn lights on the front any more. I do not want to take my bike back up to those guys due to the fact I don't trust their work any longer. Where is the most likely...

Im gitting ready to order python's turn signal's for the gen1 and before i do to know if anyone know's of a three wire turn signal that is chrome. I would like to have LED but dont know if i want to try and do the wiring and i want running lights

Took a ride today and all of the sudden i lost my guages, then it felt like i was running out of gas so i switched to reserve. well i know i have a half tank of gas left but it ran fine on reserve. so i found that i blew the signal fuse, changed it and 1 mile later it blew again. So i...

I have been asked a couple times what size resistors to use when converting to LED signals or other after market signals, so i created a spread sheet to calculate it for you, all you need to do is measure the resistance of your oem signals and your new signals and punch it in, it then tells you...

Anybody got any experience with the metric signal stabilizer, sold by Custom Dynamics? It's supposed to take the place of the 7.5 ohm load equalizers they sell. It isn't having any effect, whether I have it connected or not. Part of the reason I want to change to LED's is to reduce electrical...

Has anyone disected a signal light relay pack or otherwise found out how the internals work? Anyone draw up a schematic?? I've done the LED conversion and have the fast blink rate like everyone else. I've tried adding resistors in series in both legs of the left and right signal light circuits...

i read that somewhere but wasn't sure. i just installed a new flasher relay since going to LED turn signals and noticed there were 3 extra wires there that are not being used. it made me wonder if the vmax really does have turn signal cancellation and i wondered how it worked.... thanks, sid

ok. have a '92. just put aftermarket turn signals on it. the aftermarket signals are only single filament so i capped the running light wire and hooked up the signals accordingly. worked great!... for two weeks. now, i keep blowing the 10a signal fuse which also leaves me without a brake light...

A week ago bike started to run out of fuel after 10 mile ride. Turn signals and horn button killing dash panel power. I took left hand switch apart cleaned contacts and greased. Checked for shorts and good connector connections EJC on all of them. pulled flasher relay looks good. put it all back...

I removed my OEM rear signal lights recently to make room for my new saddlebags. I relocated some "minis" to my license plate area using a custom mounting bracket. I used some cheap incandescent types until I can afford a good set of LED's this coming off-season. But for now they're working but...

Hi, I was replacing my front turn signals and low and behold I forgot what colour did what, anyone help me with this issue? Thanks

Hey guys, about to pull the plug on some dual intensity led rear turn signals. My intent is to have them function as both running and turn signals. Wiring the turn signal portion will be straight forward. My question is on the running light wire. I was probably going to just tap into the...