Did anybody burn igniter, using wrong COP?

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
OK, I'm not going to claim the be the expert here nor have read that article in detail but there are 2 things to consider, peak current and average current - the fact the current is said to increase in the article makes me believe it refers to the latter.

Below is picture of the current in an ignition coil. Being an inductor, it takes time to reach a peak (remember your post about resistance of coil and current) , then the ignition module still supplies power (max current possible is limited by coils resistance) in order that at every rpm, the spark has the same energy.

So the peak current is the same across rpm range but average current increases with the rpm.

Actually you can determine the peak current by measuring the coil resistance, from memory original coils are circa 3 ohm, COPs around 1.5 so that gives 4.6 and 5.3 Amps (using 14v as max voltage input).

Screenshot_20210821-080907.jpg
 
From our experience there has been a correlation between CDI failures and non resistor cop installations. More people WITH cops (non-resistor type) have bought new CDI's from me (usually Ignitech) then those without them. Not all people who run non resistor cops have had CDI failures (yet). In fact the digital series of boxes (90-07) seem to be more durable. There are more of those bikes around but fewer of them have failed for any reason. Now, that could be because of the differences in the internals are better to begin with or it could be that the 85-89's are simply older. Within the last 2 years though I have sold a lot more CDI's to customers whos 90-07's have failed.

The Ignitec units allow for use with and without resistors with no damage to the unit. But it was desired for that from the start.

In the past the most common failures for the 90-07 bikes were the pickup coils. The 85-89 twin pickup to this day are far more durable and a part I sell far less often. The 85-89's CDI failures were not every usually complete. They simply would fire randomly with poor use at low RPM or poor output at high rpm. The 85-89's also have weaker sidestand relays and when they go bad the bike will crank all day long and not fire. Simply unplugging it allows the bypass.

One other thing of note,
The non-resistor COP's seem to alter the actuation timing of the vboost. I am not sure what causes that unless it's some sort of electrical "noise". It's not the same from bike to bike with some working normally and some vboost units not working at all after the swap.
 
Hi again I saw the Aug.21, 22021 post about ignitec with and without spark plug suppressors ( resistors). I just istalled the igy on my '86, after checking the ohms for the coils, wires and suppressors. I found one suppressor was 20K and the other 3 were 9K. I was thinking that I could remove the resistors from all 4 caps and still use stock resistor spark plugs. Also was going to use copper core plug wires mostly because of reliability. Are there any flaws in these ideas? reliability is a goal of mine. thanks for any help.:cool: Keep the shiny side up
 
The resistors are there to suppress radio frequency interference and electromagnetic interference and around 10K ohms is required to achieve this.
I believe that NGK plugs are around 5K ohms (?) so if you went with that you may still emit some interference. How much that is in the real world I don't know.
If your caps are original invest in some new ones, use copper core leads and the suppressor plugs and you should be fine.

Note that the thread is regarding using CoP's with the earlier ignition unit where there had been some reports of them being damaged due to the lower resistance of the CoP's relative to the coils. This would not be an issue with your set-up.
 
Responding to Seans comment about side stand switches. The one on my 2000 max failed and unplugging the unit was not enough to get the bike to start. I cut the plug end off of the switch and soldered the wires together to create a jumper, then plugged that back in and the bike started.

Just saying
 
Still running resistorless COPS on my '85. Gotta be close to 10 years now, with no problems.
 
One other thing of note,
The non-resistor COP's seem to alter the actuation timing of the vboost. I am not sure what causes that unless it's some sort of electrical "noise". It's not the same from bike to bike with some working normally and some vboost units not working at all after the swap.
If the Ignitech unit is set for fast dwell (faster 'charging' of the coils), the pulse is too narrow for the Vboost unit to sync on the RPM. Did some tests for that about 10 years ago:

https://www.vmaxforum.net/threads/the-ignitech-tci-thread.23506/post-332187
It could be that the units you sell are set to auto dwell, in which case they measure the coils resistance and then decide on fast or slow dwell. That might be why Vboost works on some bikes and not on others.
 
Back
Top