Search results

Spotted in ridgeland ms on lake Harbour dr. Had some sort of cans, a Corbin seat, and an led under sissy bar brake light. Any body here?

So I was looking on bikebandit, and they have the california needles, or the 49 state needles. Are the California needles adjustable? If so, is that the only difference?

What happens if the map sensor goes bad? Does it run rich at low rpm?

You guys obviously know what I'm referring to. The bike wave is a personalized wave you give to another person on a bike. You spend some time after you first start riding to perfect it, to make you look as cool as possible. We've all got our own variations. Mine is the delayed, two finger wave...

Well, I talked to factory pro about my wot "wet spot" below 3k. They say air correctors tend to make them lumpy in that range. marc's words: "Ok - here's my suggestion. Buy the 1.0 kit. Request 185, 190, 195 main jets (that's with a cleared MAJ) Buy the HDJ emulsion tubes. They atomize...

My bike is rich at anything less than 3k or so at wot. That's with stage 7 needles. It doesn't do it with stock needles, but I can't adjust them properly. Wouldn't drilling the slides actually make it pull the needle slower in a wot situation? It seems like it would require more vacuum, which...

I've read somewhere that the valves tend to tighten up when they go out of adjustment on these motors. Is that right? It would seem that if that's the case, the engine would pull more vacuum? If that happened, wouldn't it then pull the slides and needles out earlier? It seems my bike is doing...

I pulled my airbox off earlier today, and every time I'd throttle it up any, the slides were jumping instead of pulling up and being steady. Is this a sign of a problem, or is that from it not being under a load?

So, I've got my wideband datalogger installed, and was wondering what Afrs i should be looking for at what range at wot. I'm guessing I should be shooting for 13-13-5? I've gotten tired of guessing on this thing.

Any one know whether these bikes have a capacitive discharge or inductive discharge ignition system? I'm about to hook up a wideband datalogger, and if its capacitive, I ruin my 800 wideband.

From about 2-3k, I've got a stumble at wot. It seems probably rich, as it kinda breaks up part of the time, and riding without the airbox cover clears it up somewhat. I've leaned out the needle, and it helped some, but didn't take care of it. I've got a muscle jet kit and full exhaust. 157.5...

What are the available options? I've only found the voodoo kickstand. I've got mine shortened. It's shortened as much as possible without a good bit of work or taking a torch to it. I'm about 2 3/4 lower in the front, and about 2 in the rear. I can't really find any specs on the voodoo stand...

Here she is: Still need some wheels and inverted forks. Theres a custom brake stay coming in today as well. A lot of the black is plastidip, which I used to decide what I wanted. Will be powder coated eventually.

Alright muscle jet kit, 157.5 mains, needle at 1 1/2 clip from blunt end, stage 7 springs, slides not drilled. Runs great everywhere but off idle, cruising speeds. I'm nearly positive main jet is right, as I tried 2 above, and one below. It pulls the hardest. The needle position may be off 1/2...

I haven't started on it yet, so it may be obvious when I get into it, but what's this?

Well, I've got the dale walker pipes on, and supertrapp 12" aluminum racing series mufflers on. Morleys jet kit prolly going in tomorrow. Any one have any idea how many discs, and should I maybe go with an open end cap? I know the holeshot cans were straight through, so I figured ought not need...

I just found a holeshot full exhaust cheap, but one of the cans is half crushed. I was wondering what size the outlet is on these things. I plan on a set of supertrap universal aluminum racing mufflers (http://www.supertrapp.com/product_sections/cat.asp?CatID=34), but don't know what size to...

So, I own a 2005 Toyota x runner. For those who don't know what that is, it's a Tacoma that sits a couple inches lower with ground effects, and suspension set up for road track racing. It was set up to handle better than a 350z. Well, it comes with 235hp at the crank, and I have just landed a...

Anybody know how to upload pictures with an iPhone?

I'm about to attempt making my own forward mid controls. Just wondering if anyone else had attempted and might have some helpful hints. I'm going to use an extra right control for the right side, and just move the other side forward. Obviously going to have to make some adapters and adjustment arms.