diameter

Hi all: I hope you're all staying warm. I have a question for you: My Max is using 1994 Yamaha YZF750 USD forks with a beautiful custom-made triple tree. The triple trees have a 50mm top diameter clamp and a 56mm bottom diameter clamp. Someone has recently given me a set of 1998...

I am wanting to relocate my front signal lights on my 95 in order to put a sport shied on it.I have had a hard time finding brackets for it.I finally found some but i need to know the diameter of the stem in order to order the correct one.Anyone know the diameter of hole that I need for a bracket?

Anyone knows the exact diameter on header pipe ends as i don't have a caliper in hands? going for custom made slip-ons and i want to buy the correct size pipe.

First, yes I have used the search button but could not find an answer to my question. Does anyone know the diameter (height) of the stock tire as compared to the 240 wide tire kit? Which one is taller? Thanks MADDOG

Hi, I am replacing the stock brake and clutch master cylinders with Nissin remote resivours. I am getting 14mm for the brake (match the R1 calipers) but I do not know what size clutch diameter to get. Can anyone help please?

Hi, I am replacing the stock brake and clutch master cylinders with Nissin remote resivours. I am getting 14mm for the brake (match the R1 calipers) but I do not know what size clutch diameter to get. Can anyone help please?

Hey guys just wanted yo ask if anyone knew what the diameter of the stock brake master cylinder is? I have R1 calipers off an 02 and thinking about putting nissin remote res on just want to work out stock diameter I know R1 is 14mm.

Can anyone tell me the diameter of a stock Vmax steering stem at the point where it goes through the upper triple tree? Or the diameter hole in the upper triple tree. My bike is an 1985. Thanks

What is the diameter of a generation 1 Front Forks, I am looking at doing a headlight modification over the winter... Sent from my Galaxy Nexus using Tapatalk 2

I like this one because you can view a lot of sizes at the same time. If you don't see what sizes you want, just type them in. If you need more rows to calculate just drag the formula straight down to add as many rows as you want.

Can someone tell me if there is any difference in the diameter of the front forks between a 1986 and a 2005. I want to swap out forks and need to know if I have to change out the tree as well. I don't have the 2005 forks on hand yet, so I cannot measure them. Also, are there any overall...

Does anybody know what the stock driveshaft diameter is? Gonna be real close with my new tire and I'm trying to figure out how deep of a notch I can go with.... Sent from my HTC Thunderbolt

300mm-diameter rotors Will 300mm-diameter rotors work with the 93-07 front calipers? How 'bout with R1/R6 calipers? Is there any benefit or detriment compared to the 298mm-diametered?

I have looked exhaustively for any info on Mikuni pilot jets and all I can get are thread pitch and overall length but I NEED the dimension of the hole of the respective jets. Can anyone give me those dimensions? I need the I.D. of a #40 and a #42.5. I have all of the necessary equipment to...

I see that przemek posted this a while ago. Since then it looks like some more info has been added. I can't attest to the accuracy of the info but it seems like a good reference for anyone interested in going USD.

Does anyone know how much larger the headers are for Kerker or Marks compared to the stock header?

Hi all: Any of you know what the diameter of the Max's rear axle is? Thanks. Elimax

Anyone near a vmax that could get me the diameter of the rear differential breather cap? (the thing outlined in red)

Looks like the smallest section of the stock header is 1 1/4 diameter. Are the aftermarket versions of Marks, Kerker UFO all 1 1/2 inch?

What's the diameter of stock bars on the V-Max :ummm: I have no Vernier Calliper to check it exactly and I need to know whether Brembo MC from Aprilia Tuono will fit my handlebars or not :thumbs up: Thanks :punk: