master

Looking to upgrade my 98, as the slave keeps leaking. Questions for the forum: What parts/gasket needed? I searched the forum and read of a gasket needed and haven't found one I am sure will work, part number? Can anyone recommend a vendor who can provide a complete kit? Thanks for...

I looked on eBay, but either they're overpriced or not in the condition I'd like. Anybody have one for sale? If so, let me know what you want for it, please.

Off my 05 with 6800 miles. $40 each shipped to cont us.

ive recently bought a vmax project and ive just started doing bits to it... I bought a master cylinder repair kit for both front brake and clutch... the clutch kit came with an extra little spring and washer that was not there when I dismantled the old cylinder... ive seen on a drawing that it...

Being an inexperienced rider I made a huge mess with my rear master cylinder. Long story short : I've decided to make some maintenance to the rear master cylinder and ordered the kit. Swapped all the internal parts with the new one and mount it back on the bike. as soon as I tried to pump...

Master cylinder is from a 2006 Kawasaki EX500. Flawless condition with adjustable short lever. Works great with a single 6 piston caliper setup. Asking $50 shipped to conus. Use shawndaniels2010@hotmail.com to contact.

I'm looking for some options for both. I prefer the OEM looking ones and not the sport bike looking ones that have the big circle reservoir sticking up. I'm also wanting some replacement levers, the thick ones and wanted to know what kind as far as figment because there are so many universal...

Looking for a good setup for my '90. My original is getting weak. Looking for a good used set that hasn't been sitting around drying out or sucking up moisture. Not opposed to new if someone has parts that didn't get used or whatever. Thanks

Finally gave up trying to unclog the little hole. Found this master cylinder called Nissan off of webike Japan. Cost was about $100 as it was on sale and yen is weak. Anyway, bolted right up and did the reverse bleed and it pressurized real easy. Only downside is that it doesn't have the...

Last week, I changed to sumitomo 6 pot calipers and all was good. Today, I went ahead and swapped out oe brake lines to galfer lines, the 2 separate cables. I can't get any fluid to the master cylinder using the reverse bleed method. It feels like the banjo bolt at the master cylinder is...

Currently running a 14mm master. Looking to put stock 5/8 back on. The 14 was nice with the 320 rotor/6 pot caliper conversion but it's a tad bit spongy with dual brake setup.

Will the bike function if those two connectors are unplugged?

We are taking one last stab at finding a solution to the problems in upgrading the Clutch Master to Brembo on my 1997 Vmax. (OEM Ducati Brembo 848 1098 1198) Brake side is working like a charm, clutch not. New Barnett clutch is installed, Galfer lines, and the last attempt at trouble shooting is...

Hi All, Apologies if this has been covered, i did try a search and couldn't see what i needed. Im having some issues with the front brakes on my 1987 VMAX 1200, It all started when the brake lever would stick in when pulled. The brakes were bled to prevent the lever travelling to the...

what other bikes clutch mast cylinder will also fit the vmax? can't remember. was thinking an FJR1300?

Alright, the upper clutch master cylinder. I bought all the new parts,cleaned it thoroughly and assembled it according to the manual. My question is how do you stop it from leaking where the lever goes in? I've assembled and disassembled it 5 times and each time I start to bleed it it starts...

Good afternoon guys I was wondering if anyone has ever tried running with a 17 mm bore master and if that works okay.

Has anyone had any issues with the gen 2 master cylinder joint snapping where it attaches to the brake pedal? Mine had the bottom break off were the pin goes through 2000 miles. Seems to be a cheap casted part.

I am in need of a clutch master cylinder and mirror for an 05 VMAX. Thanks!

I ordered a rear master cylinder rebuild kit and when I took my old one off I didn't pay close enough attention I guess! Can someone tell me which way the orings go on the inside of it? I know they go on each end of the metal piece inside of it but they are tapered and I don't remember which way...