front

I'm looking for a front fender, for 85-07, any color with no cracks, must have original paint still on it. Thanks, Jim

Hello im from portugal, and my uncle have vmax 1200 1998 full power and don´t have the suport bar stock in front where the turn lights signals is mout. how can i mout the led turn signals in front of the bike ? i have this bike 1 week ago it has 13 mil kms...

Here is a question for the suspension Guru's out there. I currently have Progressive rear shocks that are 11.5's (instead of the stock 13's). currently running progressive springs in the front with a 1 inch internal lowering kit, and the forks slid up about 1/2 and inch to keep everything...

I finally decided to address my leaking front reservoir by buying a Shondy Shindy 17-651 Silver Body/Silver Lever Brake Master Cylinder Kit https://www.amazon.com/dp/B003YI9UJ2/ref=cm_sw_r_cp_api_ERKQyb60Z1QAN after reading good reviews. The question: it doesn't have a brake light switch. Any...

Hi all, I am considering replacing my front brake and clutch master cylinders/ handles/ reservoirs, mainly because of a screwed up (pun intended) bolt that keeps the lid on the front brake reservoir (I brought this up in another thread, but affordable machine shops in Brooklyn are hard to...

Can't seem to find an answer to this, but is there any functional difference in the factory front wheels? I like the way the 85's look, but I wouldn't want one if it is heavier or weaker.

Just installed front 6 pod calipers from a 95 FZR1000 and new EBC HH pads on my 97 Max..wow what a difference....had to lower the dist block down an inch to make lines work(IMO...or in my comfort zone) until I order steel lines...bolt on using stock master cylinder....see pics....Thank you Sean...

It got up to 60 degrees today so I figured it was time to take my new steed out for a ride. I have not ridden street bikes in a little over 10 years. I used to ride a ZRX. The front brake didn't feel like it had enough stopping power. Since I'm new to the Max I didn't know if this was...

What did I do wrong? I replaced my seals and installed new Progressive springs.......now, I have no give in forks! I used stock spacer, but, I didn't think it needed to be cut down, about 5/8" more above tube at install. added the 4 and 3/4" from top fork oil level, installed the caps, now...

My front left turn signals won't work on my '96 (one mounted on fork, one in the mirror). I just got this bike and I'm not familiar with the max's wiring; where should I start in diagnosing this? Everything looks hooked up too.

I replaced a warped rear about 6 months ago. Now, I have a warped front rotor. Bars shake during freeway on ramp launch, I can no longer take my hands off the bars and coast. I can spin the front tire and clearly ID offending rotor. I have fresh pads, fork seals, and head bearings...

I have noticed every time I go for a ride, even short hops of 10 miles or less, I have oil blowing on left side on top of stator case cover. It,s coming from looks like lower cylinder or base gasket. I am assuming this means that I must pull engine and do top end? Shops around here will no...

So I'm a jackass, and I make a lot of mistakes. Luckily I'm learning a lot along the way. A screw for my front brake reservoir was stripped, so I decided to drill a pilot hole and use my bolt extractor bit to get it out. Well, the head of the screw ripped off, and I now have an unclear amount...

Hello, I have an '06 vmax and I'm getting ready to install my COPS. How do I remove the front seat to get to the coils? Please let me know. Thanks, Jamie. Sent from my SM-N920T using Tapatalk

I need your assistance guys. I have a 2009 VMAX and the front forks have started leaking. I am in Beirut, Lebanon and the dealer here cannot find the seals locally. He also does not know the part number for the seal. I went online to www.shopyamaha.com and they also do not have the VMAX listed...

Hi guys, I am following up on my post about my VMax being run over by a 4900 lb ML35 SUV (yes with me on it...). The good news is all is well with me and most of my VMax. Got some insurance money and the mod monkey is securely perched on my back... First thing I need is a front...

2001 in need of a correct front fender. Let me know what you have, pics please. thanks!

2001 in need of a carbon fiber front fender in good condition. Let me know what you have and pics, please.

what is the most likely cause? tweaked fork or issue with the fork brace? causes a tiny cant in handlebar when riding. new to me 2001 and just getting ready to dive in to a few minor issues needing correction before I ride it. looking for suggestions, tia!

Need some help guys. My father in law vmax needs new front wheel bearings. Stock "96 wheel. How do u get the bearings out of the wheel? Cant get them out with a screwdriver of something becouse of the axle hole? Any tips to get them out. In 1 piece?