setting

Long story short, I made a few mistakes while putting in a new clutch (with DD mod) and upgrading the shift segment. The first mistake was I forgot to push the shift rod all the way to the left before tightening the nut on the shifter. I went for a test ride, shifted to 2nd, then shifted...

Installed a harlan shift light a couple weeks ago. I set it for 8800. What are you guys setting yours at? How far past redline will it start hurting the bike? Sent from my SM-G920P using Tapatalk

Does anyone know the stock Canadian needle clip setting? I'm at sea level. I get a stumble cruising at 45000-5000 rpm. When I get on the throttle it goes away untill I start cruising again. I think it is running rich. I have stock modified exhaust.

Edited for content

Does anybody know what the spark plug gap setting should be on a 2007 if you have a stage7 jet kit ?:bang head:

Does anyone know what the spark plug gap setting should be if you have a stage 7 tuned on 93 octane ? Thanks ahead of time for you help.

So this might be a dumb question but I just notices a P on my ignition switch and was wondering what it's for/denotes. I haven't been able to get my key to go over to the P no matter which way I have the handle bars or if I push down on the key. I'm hoping that its some extra security in case...

I

Setting all four A/F screws blindly to 2 1/4 turn. Is that OK? Hi Appreciate your comments and suggestions. I'm really not knowledgeable enough about carb. Anyway here's the story. Stock carb, custom exhaust. The PO messed up. Carb setting was way off. On idle the bike seemed to be...

http://www.digital-speedos.co.uk/setting-up-rpm-guide-289-p.asp The link above describes how to install the RPM gauge. To my knowledge I have all my wires set up correctly. Can someone explain what exactly "HT Lead" means? I have been told I need to wrap the wire around the coil wire. So...

I have a 2003 VMAX and just cleaned the CARBs. I noticed that all four pilot screws were screwed all the way in. When I looked at the service manual it said they were "Preset". I thought that it was odd that they would all 4 be "preset" to all the way in, I am used to them being backed out 1-3...

Short question: My ignition switch has an on/off and "P" position. In order to turn it to the P position, you have to push the key in and then rotate it. I could not find anything on the P position. What does it do? Long question. Well, the question is actually...WTF?? I rode my 88 Vmax a...

I got a little fed up with trying to use calipers on the rounded surfaces of the float chamber and float itself so I snipped this little deal out from the plastic cap of a vitamin bottle. There are probly several ways to fab this thing but I started with a carb that was already adjusted and...

I believe Bill Warner is one of the brothers behind Wild Brothers where a lot of Vmax guys get their parts. Check him out! This is STUPID FAST!!! Oh and a record! http://www.autoblog.com/2011/07/20/watch-bill-warners-record-setting-311-mph-motorcycle-run/#continued Way to go Bill!

what tool are you guys using to measure the floats dry on the bench ?

At cold bike idles at ideal setting (getting 14V) however after warmed up it seems to drop slightly to 900ish (13 V) and I have to give a little gas to get it back to 1000RPM. What is the cause of the drop? Solutions?

What is the best way to set the float height when you asemble your carbs after cleaning? I am aware of the external hose method but would like to get them as close as possible when putting them back together.

What is a good rpm setting for a shift light to get the best result?

I read in the manual that you can add air to the front forks. I'm 220 fully geared up. What suspension settings are most of you guys running with stock suspension? How much air in the front and what compression/rebound/preload setting on the back shocks? when i pull up in my driveway i...

Can someone please tell me what the torgue setting is for the oil change bolt ??? Is there a torgues setting for oil filter? Thanks