aftermarket

I'm buying a tach http://procycle.autometer.com/CatalogGaugeDetail.aspx?gid=134 Do we have a one or two pulse system? When I install it, can I just use the stock grey wire or do I go to a coil?:ummm: The directions for it are here: http://procycle.autometer.com/pdf/19201_instruction.pdf...

OK, I'm installing a new temp gauge...... Can I use the stock sender or do I have to use the one that came from Autometer?

Just wondering what type of aftermarket wheels everyone is running carrs,bbr,dymag,ufo,coo,degret,kosman ect. and so on. i would like to get a feel of what everyones likes the best about there wheel of choice and would the buy them again also there fit and finish plus overall satisfaction. so...

Ok I installed my new tach but when hooked up to the stock wire it just did not seem like it was just right so I tried hooking it up to the common wire for the coil fairly close to the coil and that works not at all I was wondering if this is b/c I installed the COP or am i missing something?

i was poking around on ebay and came across a few new aftermarket items for the 09 max. if i knew how to post a link, i would. type in 2009 vmax and they should come up. the seller is the guy who owns python motor sports. billet swingarm caps (120366600206) and billet infills...

i just saw this on another forum i go to and thought the guys here would be very interested!! http://www.bikeland.org/board/viewthread.php?FID=49&TID=43822&set_time=1229825521 i knew it would be just a matter of time before someone figured out how to bypass the speed limiting circuit, now...

I've got a set of Progressive 440 rear shocks that are 12" eye to eye. I wanna get my bike up a lil higher for a lil better handling. These were great til i put on the USD and the 17" rear wheel/tire, now the whole bike is lower than i want it. The shocks have 190lb springs from what i was told...

Are there better aftermarket gaskets out there? Or are the stock Yamaha ones our only choice? If so, are there any tricks to getting a better seal in the long run??

I have 3 H-beam rods from a V-max. There are no markings at all anywhere on them except two have a small "U" on one end of the cap, and the 3rd has a small "J". I'm thinking they are Carrillo but not sure. Also where would be a good place to send them to make sure all is A-OK?

From what i've found, most of the aftermarket LED signals are only a two wire setup, which does not allow the use of the factory running lights. Someone may have a fix for this but i was unable to find it in my searching. Anyway, i used a tail light "integrator" that i purchased at AutoZone for...

Still chasing problems on my bike. Still sputters. Is it worth buying an aftermarket ignition module or should I just stay OEM?

Now that I have instaled 17" wheels and USD forks, I find myself grinding the pegs way more often. I need more clearance. Im looking for pegs like cycleoneoff sells. These offer little more clearance. cycleoneoff sells GP brand pegs and I found them at other places, for $25.00 cheaper, but...

Based on what's reportedly being delivered with the new Max, my needs are going to be small. My bike will likely remain largely stock, except for possibly these, if/when available: Small windscreen Engine guards Aftermarket pipes (come on Mark, get busy!) In addition, especially...

Does anyone know if there are any sort of aftermarket piston selections readily available for the VMax- high compression or otherwise? Thx! :) john

Anyone can tell me if there are any aftermarket parts dealers? After 22 years it can't just be what they offer at the dealership or on the yamaha website. For instance 87-93 mustangs have aftermarket parts and dealers who make parts just for the 5.0s. Now that I am sure I have over explained...

I am looking for a full exhaust. marks, hindle, kerker. anything but a cobra. looking to buy used to save $. I will have a 2003 full stock exhaust to sell. I am in Scranton PA. call my cell 908-783-8734 Paul

I was wondering ...what's the average amount of HP gain from an Aftermarket exaust? I'm thinking all of them will come within 1-2 HP from another....but has anyone ever dyno'd a bike with just the exhaust...no other mods?????

Does anybody have an aftermarket tach and do they like it? What brand and size? I would like to find something for on top of my speedo hopefully with a shiftlight .