motor

Alright I have an older thread that could explain how this may of happened if this is actually an issue. http://www.vmaxforum.net/showthread.php?t=17128 Now, when looking at my motor I see what could be a problem, I am not sure if I am seeing problems where there are none or this is a very big...

My simple Tranny repair is turning into a full blown Mod Monkey freak out. I can't stop myself! With Seans knowledge, advice and coordination and me bolting stuff together my motor is going to 1360,............ doing stroker crank, rods, and 13:1 over bore pistons and biggers cams, valve...

so i had my carbs apart several times in an attempt to rebuild renew and stop a sticky float issue. now that i have reassembled my carbs and installed them for the 3rd time one of my slides is not moving when i rev the engine. i can manually move it and it has approximately the same action as...

ok i dont no where to ask this ?................... what is a vmax motor worth 2nd gear is bad:confused2:. i think it a 92 with 15000 miles on it not sure tho. thanks to all. bill:punk:

Hello Guys, I'm thinking of buying (importing) a used engine for my 99 Vmax 1200 either from US or Europe. Searching google I didn't find many places selling Vmax motors. Can you point me to a place (web site) of a dealer selling these stuff? Thank you very much, Adi Barda

Is there any difference in using the delrin or aluminum motor mounts in a Gen 1? Wear and Tear or vibrations? Also looking for a luggage rack other than Mek out there?

Or specifically, the engine in my Yamaha RX-series snowmobile. The "genesis extreme", or a tweaked/tuned for snow R1 engine. 1000cc I4, quad carbs. Motor is all stock except for muffler(equivalent of slip-ons to a bike). Anyway, I was out riding today and got onto a lake. Absolute perfect...

Going up to Schenactady Ny to get my 1500 motor cant wait to see the #s will be going up Jan 2 if anybodys close to Pcw give me a shout maybe we can grab some lunch or support the single moms,lol

While looking at solid motor mounts, I have found a lot of people have installed both solid motor mounts and frame braces. Given the solid mounts should turn your engine into a brace can any one explain the benefit of both modifications? Specifically has any one installed the solid mounts...

do i have to remove the swingarm inorder to remove the driveshaft so i can pull the motor?

We are doing a group buy setup for solid motor mounts on the Venturerider.org site. One of our members is getting them for $50 for the set of six. Including shipping to US addresses. Machined from 6061 Aluminum. Same mounts are used on the 1st gen Vmaxs. If anyone is interested let me know...

I have a flywheel form 85 VMAX, will it work on my 95 VMAX.

This just started while I was out for a ride last night. Pretty randomly(but several times a minute) I hear what could be called a low-pitched screech from the engine case. Sometimes it lasts just an instant, other times as long as a second. The pitch varies a bit too, but doesn't seem to...

Riding around, started hearing some very pronounced rattlingfrom the left case when I let off the throttle in any gear. After a few miles of that, I'd let off and it it was jerking the wheel hard enough to just about lock up the tire and vibrated like crazy. Shortly thereafter, let off in second...

Only when I use the left blinker I get a miss in the motor...When the blinker is turned off its fine...Its fine with the right blinker..Both blinkers work the same and blink fine...Strange..Help

where can i order some solid motor mounts? i like the shiny ones

I am installing motor back in with new solid motor mounts. I am running into a snag with my rear motor mounts. The stock bolt is bigger od than the id of the solid motor mounts. Do I have the wrong size solid mount or should I just get a smaller od bolt and go all the way through with a washer...

I got my 2 boost modules from Sean today. Now I have another problem. "when I turn the key ON" the black slider block does not open all the way....it lifts and drops 5 times in a row, only lifting the block a 1/4 of the way, then stops. I try it again...this time it lifts slower, but still...

I've found aluminum or delrin mounts. Any thoughts? Seems like the aluminum would transfer vibrations better but I'm not sure if there are any other factors I'm missing. If anyone has any advice I'd appreciate it!

Found a 85 max for sale with this claim. Fresh rebuild.. Thought vance & hines did HD exhausts.:ummm: