HD oiler question

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

ptnov

Well-Known Member
Joined
Aug 4, 2012
Messages
113
Reaction score
0
Location
Stockholm
Hi

I'm trying to install the Sean's HD oiler kit. When I removed the clutch basket i saw that the gear already is yellowed plastic does this mean that the HD oiler kit already is installed. Also the orange o-ring has a black o-ring over it, and it is still unpopped.

Also how should i reuse the bendable tab that locked the 30mm nut? If so how do I install it? bend it after or before screwing the nut back in?

Here's a pic of my gear currently inside.
15pfifm.jpg


Here's a pic of the o-ring you can barely see the orange o-ring
2e5twsk.jpg



Thanks!
 
Hi

I'm trying to install the Sean's HD oiler kit. When I removed the clutch basket i saw that the gear already is yellowed plastic does this mean that the HD oiler kit already is installed. Also the orange o-ring has a black o-ring over it, and it is still unpopped.

Also how should i reuse the bendable tab that locked the 30mm nut? If so how do I install it? bend it after or before screwing the nut back in?

Thanks!

The small yellow gear in your photo is driven off the clutch basket, it will remain in place. The large yellow gear is the driven oil pump gear, it will be re-installed also. You are changing the oil pump drive gear. It is not shown in your photo. It rides on the opposite end of the shaft that is driven by the clutch basket gear. If yours is stock, it will be metal.

I've reused the clutch lock washer without issue on many bikes. Install it flat and then bend one of the tabs against the nut after installation. I only replace them if it seems like one of the tabs is ready to crack. You don't want any metal pieces floating around in the oil
 
The small yellow gear in your photo is driven off the clutch basket, it will remain in place. The large yellow gear is the driven oil pump gear, it will be re-installed also. You are changing the oil pump drive gear. It is not shown in your photo. It rides on the opposite end of the shaft that is driven by the clutch basket gear. If yours is stock, it will be metal.

I've reused the clutch lock washer without issue on many bikes. Install it flat and then bend one of the tabs against the nut after installation. I only replace them if it seems like one of the tabs is ready to crack. You don't want any metal pieces floating around in the oil

Ok! so I have to keep digging in the clutch.

What kind of tool do you use to bend the tab? I used a punch to open it, but i can't punch it back..
 
You should not need to "dig into the clutch" any more than you have. You need to remove the oil pipes on the bottom of the engine. Then you have to remove the oil pump.

Once the pump is out, you will see the drive gear that needs replaced. To remove that gear, you need a set of 90 degree snap ring pliers.

I just a pair of "channel lock" pliers to start bending the clutch lock washer. Once side of the pliers on the clutch nut, the other side on the washer. Squeeze and it will start to bend. Once its bent a little bit I use a hammer and punch to flatten it against the nut.
 
alright I'll look into that tomorrow. Is there anything holding the oil pipes or do you just pull it out?
 
You gotta wiggle it but follow the bracket it is welded to. There is a bolt head that is holding her down or up or on, however you are looking at it. You do have a manual don't you?!
 
The "oring" pipe will come out with the oil pump. The black puck on the bottom of it is what keeps the pipe/oring in place via pressure from the oil pan when bolted up. The other oil pipes I just loosened to get the pump out.

Dale
 
The "oring" pipe will come out with the oil pump. The black puck on the bottom of it is what keeps the pipe/oring in place via pressure from the oil pan when bolted up. The other oil pipes I just loosened to get the pump out.

Dale

The pipe with the "dreaded orange o-ring" is not attached to the pump. It attaches to the oil pipe system that bolts to the block.

Here is a photo. The orange ring was replaced with a black one though.



And another that shows the layout a little better

 
Do you have to use any other gasketing besides the supplied gaskets for clutch and oil pan or are they enough?
 
PCW does their bracket a little differently, notice no rubber bump pad needed. Also, I think the oil pickup is shimmed to ride lower in the oil pan.
Here is a pic of mine:
os-2.jpg

os-3.jpg

os-5.jpg
 
I Just stripped one of the 3 oil pump screw holes. Will loctite be enough to hold these screws in? It it fingertight atm.
 
Good GOD. Be careful when you remove that inner oil pump drive gear. You could lose the snap ring or the washer like I did. stuff everything with cloth and make sure you have the correct washer. There are two in the kit and only one will fit the oil pump drive shaft. The other one is a shim for the oil pump relief valve spring.
 
Good GOD. Be careful when you remove that inner oil pump drive gear. You could lose the snap ring or the washer like I did. stuff everything with cloth and make sure you have the correct washer. There are two in the kit and only one will fit the oil pump drive shaft. The other one is a shim for the oil pump relief valve spring.

Did that! I used a short 45 degree expandable plier and corrected the snapring with a screwdriver.

Any of u guys know if it's safe to lock a stripped thread for the oil pump with loctite? Only the top 4 threads was stripped and it's in little more than fingertight...
 
Can you run a tap through it to clean up the trhreads?

The threads came out with the screw. Can a tap make the same size screw fit or only bigger screws?

It's now locked in with loctite 243. It's supposed to be oil tolerant. Not sure if it'll do though. I'm gonna try to confirm that it works or find another way to fix it before putting back the oil pan.
 
If you only pulled out the last few threads I would think it's fine. You can try and see if a longer bolt will fit in there and torque to spec.



Sent from my SM-G900V using Tapatalk
 
get some longer bolts. there is enough room for that next size. fastenal or hardware store. 6mm x 1.0 pitch
 
Back
Top