R1 calipers

VMAX  Forum

Help Support VMAX Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Sweetwilliebrownjr

Well-Known Member
Joined
Feb 11, 2010
Messages
175
Reaction score
2
Location
Jackson, Ms
Thinking about upgrading the brakes. I've got an 05. What year r1 calipers will fit, and does it require different pads than stock? Any other helpful info would be appreciated as well.
 
Re: R1 calipers retro fit

Say hey Willie. I'm thinking 1999 through 2003 R1 calipers are exact fit in 1993 (big tube) forks and later. Pre 93 require a relocation bracket. Pads are stock R1 pads. Think about stainless brake lines while your at it! Morley Muscle has everything you need. Patmax
PS. Right front R1 caliper is also plug and play on the rear too!
 
Busa parts are for the early forks. I occasionally have some direct bolt on 6 piston calipers but am out of stock at the moment. They are very hard to find and I only get a set or two a year. Most will be happy with the R1's that were noted. I do also believe the warrior calipers as well as maybe even the raider may work.

Sean
 
The R1/R6/Warrior NON-Radial calipers are all direct bolt on's for 93-07 Vmax's. If the bolts are through the side into the fork then it's the same. The radial (monoblock) calipers have the bolts passing downward into the fork and will not fit.

Sean
 
Sean, whats the difference between an R1 caliper and the late Vmax? Both are 4 piston, so it has to be the diameter of the pistons is larger......or ???? I guess I am wondering why you would want to change them?
 
The vmax/fzr calipers are cast. The R1/R6 and milled. Little bit better control of tolerances and I think the passages are just a little tighter. I haven't checked the bore of the pistons but that may be the biggest difference if there is any.

Sean
 
How is a right front r1 caliper plug and play on the rear when the bolt holes are about 3/4 of an inch further apart on the r1s?
 
We are discussing the front calipers for 93-07 forks. To use it on the rear requires a custom brake stay (and rotor) or maybe even a custom adapter from Jedi (we don't make that particular adapter though we have made one for the busa 6 piston rear use.)

Sean
 
Yea. I just fitted a wave rotor on the rear, and with the OEM caliper, S/S line and HH pads I'm having to readjust my foot pressure quite a bit - I keep locking the rear wheel and screeching the tire!

The rear brake is most definitely well strong enough as it was - I only put the wave rotor on to match the fronts so it's just a cosmetic thing really..
 
Need to ask Dave (Yukonerdave) and see how well it works for him. I am not sure but the theory was it should take more lever travel but less effort thus giving a better "feel" and taking away the harshness when you hit the pedal.

Sean
 
Well, with some cutting, grinding and alot of 3M scotch Brite pads, I actually made the front stock caliper fit the rear. I had to basically make a second small brake stay and cut the top caliper bolt hole out and bridge from the caliper to the original brake stay with the new one. It was around 2 inches long. Also a bit of work spent on grinding the face where the bottom bolt goes in for the small amount of clearance needed. It works great, but I still want one of the custom setups to make it look cleaner.
 
Up on centerstand, pull the axle half way out. Unbolt caliper and hang it out of the way, pull the rotor bolts, tap rotor with rubber mallet. It should drop right out or should I say fall off. No need to drop wheel off the differential. Don't forget to pay attention to any washers between brake mount, wheel, swingarm
 
Up on centerstand, pull the axle half way out. Unbolt caliper and hang it out of the way, pull the rotor bolts, tap rotor with rubber mallet. It should drop right out or should I say fall off. No need to drop wheel off the differential. Don't forget to pay attention to any washers between brake mount, wheel, swingarm

I say good luck pulling the rotor bolts without dropping the wheel..

I used an impact driver with the correct bit and they still wouldn't come out! The blue loctite seizes pretty bad with age. I needed to use a center punch and hammer to get them out, and they all needed replacing. :confused2:
 
Yea. I just fitted a wave rotor on the rear, and with the OEM caliper, S/S line and HH pads I'm having to readjust my foot pressure quite a bit - I keep locking the rear wheel and screeching the tire!

The rear brake is most definitely well strong enough as it was - I only put the wave rotor on to match the fronts so it's just a cosmetic thing really..

I did the same :)
 
Back
Top