kit

Hi, I just bought Seans Jet kit. Do I have to remove the carbs to clean the inside and rejet or can i do while it's still on the motor? Thanks!

Just put My stage 7 in over the weekend and just ran across this..:punk: So if anyone is looking a for one heres your chance:confused2: 2 weeks ago I would have been trying to get it..:rofl_200: 17 hours left...

Are there any instructions for the HD oiler kit install or just the picture here: http://www.morleysmuscle.com/muscle-bikes/vmax/engine/hd-oiling-cure I'm trying to figure out the best way to loosen the 30mm nut that holds the clutch basket in place. I don't have a impact driver and would like...

looking to rebuild my carbs that were jetted by previous owner...here is the problem...local yamaha dealer shut down and the closest one is now an hour and a half away....does anyone just have a complete kit? maybe one with a good jet kit so i know what i have?....oh and a sink tool too?:ummm:

Hello folks, and Happy New Year! I've just installed Mark's stainless 4-2, 2" exhaust and the bike started running lean / lacked torque. Then installed Morley's Jet Kit with needles on 4th clip, Mains 160 (2300-2500 ft elev, 47 degrees outside) and I suspect it's running too rich. The...

My cousin wants a Gen 1 Vmax but only if he can get a wide tire kit. He is talking 300 wide. I know this requires a swing arm and likely a chain conversion. What options are out there, new or used? Thanks!

My '98 Vmax clutch & Bracke reservoirs leak or sweat even though I installed new gaskets. The paint is almost gone and I would like to install something new but don't want to go back to OEM. I've seen sets similar to the picture below but they seem to only fit second gen Vmax. They leak and...

Got these from a random guy I met at a gas station, he used to have a VMax and had these sitting in his garage. He had just the springs, but when I did mine it came with extra lowering springs and spacers. Spacers are uncut and lowering springs included have never been used. Progressive springs...

Hi. I'm in search of a complete factory Vmax tool kit. Please let me know if you have one and price. Thanks.

So now that I have the racing bug, I have a question. I ran 7.28 (1/8th) with several other passes in the low 7.3's. my 60 ft times were around 1.8 with a best of 1.77. I see I have room for improvement on the 60 ft, so with pratice I can see being consistantly in the 7.2's. Would a jet kit, set...

is there a big differance over Seans jet kit set up over a Dynojet kit besides the Dyno jet kit i think runs maybe around 100.00 and has no modified airbox .I have a two brothers racing 4 into one header and exhaust set up .I am not sure what i am running for jets but i get 30mpg even when i...

Curious as I pulled my slides out today and noticed they where drilled. The needles are fat and non adjustable. So I am assuming those are stock. My stage 7 needles are thin and adjustable. I am not sure what is in my carbs. But my Stage 7 carbs have 190 DJ jets for the mains and...

I see you build some sweet engines on your site, do you offer a complete kit I could buy for my 85 and overhaul it completely with a 1500 big bore? do the stock rods handle this upgrade ok?

Hey guys, I picked my bike up from the shop that jetted my bike they tuned it by ear.... It didn't seen to bad going around the block... When I got on the highway I noticed it was really rich and was loading up at crusing speed. Under wide open throttle it seems very rich as well... I have a...

edit

I have an '88 V Max with a Magnacharger and was wondering if anyone makes a NO Kit for this set up ? Thanks Chad

How hard is it to install a jet kit? What would it do performance-wise...I have a full exhaust system and a K & N filter?

Hi. What V-boost setting would you recomened with a muscle-kit for most power? I'm having it installed and setup next week and wondered if it needs to be left in the v-boost setting it's setup in; ie 3.5k or 6.5k rpms. Either that or have it on full time. I've a full exhaust system if thats of...

I just went for a ride after putting in my Morleys jet kit. My setup is I used Seans needles (stage 7?) Put in the air correctors 157.5 mains STD springs Idle screws 3.25 turns out V-boost programmed to start opening just before 4000RPM Seans airbox lid Marks exhaust 4 into 2 The main...

I have tried searching using words like morleys muscle jet install* fit* blah blah blah and I get like a gazillion posts that have some of those words in it. Is there a how to guide anywhere? The instructions on Seans website are pretty short, and I can't work out what I should do to start...